Differences

This shows you the differences between two versions of the page.

--- student_documentation:jm3 [2024/03/30 07:57] – Marco Schmid
+++ student_documentation:jm3 [2024/04/26 13:59] (current) – [BE] Joe Redfield
@@ Line 1: / Line 1: @@
-====== Joulemeter (JM3) ======
+====== Joulemeter (JM) ======
 {{:student_documentation:jm3.png?nolink&450|}}
@@ Line 40: / Line 40: @@
   - Secure the Joulemeter with Velcro or cable ties ensuring the LEDs are visible and the on/off push button is accessible.
   - Reconnect the battery to the vehicle electrical system.
-  - <color /#FBCE07 >For Urban Concept ICE vehicles</color>: onnect the CAN cable to the Joulemeter and the On-Board Computer (OBC).
+  - <color /#FBCE07 >For Urban Concept ICE vehicles</color>: connect the CAN cable to the Joulemeter and the On-Board Computer (OBC).
 ==== ICE ====
@@ Line 46: / Line 46: @@
 <color /#FBCE07 >For Prototype ICE vehicles</color>,
-no Joulemeter data cable will be used. Installation diagram: {{:student_documentation:2024_prototype_joulemeter_checklist_ice.pdf | Joulemeter installed in BE}}
+no Joulemeter data cable will be used.
+Installation diagram: {{:student_documentation:2024_prototype_joulemeter_checklist_ice.pdf | Joulemeter installed in ICE}}
 <color /#FBCE07 >For Urban Concept ICE vehicles</color>,
 wire the Joulemeter data cable in series to the [[student_documentation:lfm|Liquid Flowmeter]] using two CAN cables and a [[T-Splitters|T-Splitter]] mounted on to the LFM. Connect the Joulemeter as the second device following the [[student_documentation:lfm|Liquid Flowmeter]]. At the Backbone, use the connector marked „SENSOR“.
-For the JM3, use the USB cable for charging only! See charging instruction below.
+For the JM, use the USB cable for charging only! See charging instruction below.
 <color /#FBCE07 >For ICE vehicles using hybrid technology with a Supercap</color>,
-a second JM3 will be used to measure Supercap voltage.  Install wires from the Supercap positive and negative leads to the JM3 positive and negative input connections.  Connect the JM3 to the CAN network with the help of the T-Splitter and an additional CAN cable. There is no required order of JM3s in the CAN connections.
+a second JM will be used to measure Supercap voltage.  Install wires from the Supercap positive and negative leads to the JM positive and negative input connections.  Connect the JM to the CAN network with the help of the T-Splitter and an additional CAN cable. There is no required order of JMs in the CAN connections.
 {{ :student_documentation:icejoulemeter.png?nolink&300 |}}\\
 Joulemeter electrical installation (ICE)
-See also [[[[student_documentation:ice|ICE installation schematics]]
+See also [[[[student_documentation:ice|ICE installation diagrams]]
 ==== BE ===
@@ Line 65: / Line 66: @@
 <color /#FBCE07 >For BE Prototype vehicles</color>,
 no data cable will be used.
+Installation diagram: {{:student_documentation:2024_prototype_joulemeter_checklist_be.pdf | Joulemeter installed in BE}}
 <color /#FBCE07 >For BE Urban Concept vehicles</color>,
-connect the JM3 data cable to the „SENSOR“ outlet of the [[student_documentation:bb|Backbone]].
+connect the JM data cable to the „SENSOR“ outlet of the [[student_documentation:bb|Backbone]].
-For the JM3, use the USB cable for charging only! See charging instruction below.
+For the JM, use the USB cable for charging only! See charging instruction below.
@@ Line 76: / Line 78: @@
-See also [[[[student_documentation:be|BE installation schematics]]
+See also [[[[student_documentation:be|BE installation diagrams]]
 ==== H2 ====
@@ Line 82: / Line 84: @@
 <color /#FBCE07 >For Prototype Hydrogen vehicles</color>,
 no Joulemeter data cable will be used.
+Installation diagram for H2: {{:student_documentation:2024_prototype_joulemeter_checklist_h2.pdf | Joulemeter installed in H2}}
+Installation diagram for H2 with Supercap: {{:student_documentation:2024_prototype_joulemeter_checklist_h2_supercap.pdf | Joulemeter installed in H2 with Supercap}}
 <color /#FBCE07 >For Urban Concept Hydrogen vehicles</color>,
-connect the JM3 data cable to the „SENSOR“ outlet of the [[student_documentation:bb|Backbone]].
+connect the JM data cable to the „SENSOR“ outlet of the [[student_documentation:bb|Backbone]].
-For the JM3, use the USB cable for charging only! See charging instruction below.
+For the JM, use the USB cable for charging only! See charging instruction below.
 <color /#FBCE07 >For vehicles with a Supercap</color>,
-a second JM3 will be used to measure Supercap voltage.  Install wires from the Supercap positive and negative leads to the JM3 positive and negative input connections.  Connect the JM3 to the CAN network with the help of the T-Splitter and an additional CAN cable. There is no required order of JM3s in the CAN connections.
+a second JM will be used to measure Supercap voltage.  Install wires from the Supercap positive and negative leads to the JM positive and negative input connections.  Connect the JM to the CAN network with the help of the T-Splitter and an additional CAN cable. There is no required order of JMs in the CAN connections.
 {{ :student_documentation:h2_joulemeter.jpg?nolink&400 |}}
-See also [[[[student_documentation:h2|H2 installation schematics]]
+See also [[[[student_documentation:h2|H2 installation diagrams]]
 ===== Handling =====
@@ Line 120: / Line 124: @@
 <color /#FBCE07 >For Urban Concept Vehicles</color>,
-The JM3 will be supplied with a fully charged battery.
+The JM will be supplied with a fully charged battery.
 If the device is only switched on when connected to a running OBC, the battery will last for the whole event.
@@ Line 129: / Line 133: @@
 {{:student_documentation:jm3:charging_adapter_dimensions.png?direct&400|}}
-A fully chargend Batery will last for at least 4 hours.
+A fully charged Battery will last for at least 4 hours.
-Charging a fully depleted battery will take about 3 hours.
+Charging a fully depleted battery will take about 3+ hours.
 **Characteristics**

User Tools

Site Tools

Differences

Page Tools