This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
student_documentation:jm3 [2024/04/23 14:15] – [Installation at event] Joe Redfield | student_documentation:jm3 [2024/04/26 13:59] (current) – [BE] Joe Redfield | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Joulemeter (JM3) ====== | + | ====== Joulemeter (JM) ====== |
{{: | {{: | ||
Line 51: | Line 51: | ||
<color /#FBCE07 >For Urban Concept ICE vehicles</ | <color /#FBCE07 >For Urban Concept ICE vehicles</ | ||
wire the Joulemeter data cable in series to the [[student_documentation: | wire the Joulemeter data cable in series to the [[student_documentation: | ||
- | For the JM3, use the USB cable for charging only! See charging instruction below. | + | For the JM, use the USB cable for charging only! See charging instruction below. |
<color /#FBCE07 >For ICE vehicles using hybrid technology with a Supercap</ | <color /#FBCE07 >For ICE vehicles using hybrid technology with a Supercap</ | ||
- | a second | + | a second |
{{ : | {{ : | ||
Joulemeter electrical installation (ICE) | Joulemeter electrical installation (ICE) | ||
- | See also [[[[student_documentation: | + | See also [[[[student_documentation: |
==== BE === | ==== BE === | ||
Line 70: | Line 70: | ||
<color /#FBCE07 >For BE Urban Concept vehicles</ | <color /#FBCE07 >For BE Urban Concept vehicles</ | ||
- | connect the JM3 data cable to the „SENSOR“ outlet of the [[student_documentation: | + | connect the JM data cable to the „SENSOR“ outlet of the [[student_documentation: |
- | For the JM3, use the USB cable for charging only! See charging instruction below. | + | For the JM, use the USB cable for charging only! See charging instruction below. |
Line 78: | Line 78: | ||
- | See also [[[[student_documentation: | + | See also [[[[student_documentation: |
==== H2 ==== | ==== H2 ==== | ||
Line 89: | Line 89: | ||
<color /#FBCE07 >For Urban Concept Hydrogen vehicles</ | <color /#FBCE07 >For Urban Concept Hydrogen vehicles</ | ||
- | connect the JM3 data cable to the „SENSOR“ outlet of the [[student_documentation: | + | connect the JM data cable to the „SENSOR“ outlet of the [[student_documentation: |
- | For the JM3, use the USB cable for charging only! See charging instruction below. | + | For the JM, use the USB cable for charging only! See charging instruction below. |
<color /#FBCE07 >For vehicles with a Supercap</ | <color /#FBCE07 >For vehicles with a Supercap</ | ||
- | a second | + | a second |
{{ : | {{ : | ||
- | See also [[[[student_documentation: | + | See also [[[[student_documentation: |
===== Handling ===== | ===== Handling ===== | ||
Line 124: | Line 124: | ||
<color /#FBCE07 >For Urban Concept Vehicles</ | <color /#FBCE07 >For Urban Concept Vehicles</ | ||
- | The JM3 will be supplied with a fully charged battery. | + | The JM will be supplied with a fully charged battery. |
If the device is only switched on when connected to a running OBC, the battery will last for the whole event. | If the device is only switched on when connected to a running OBC, the battery will last for the whole event. | ||
Line 133: | Line 133: | ||
{{: | {{: | ||
- | A fully chargend Batery | + | A fully charged Battery |
- | Charging a fully depleted battery will take about 3 hours. | + | Charging a fully depleted battery will take about 3+ hours. |
**Characteristics** | **Characteristics** |